Steel Anchors 2

Approx. Rs 121 / Piece Get Latest Price

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 197 / Piece Get Latest Price

The economical solution for all standard fixings.

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 1,764 / Piece Get Latest Price

The fischer bolt anchor FAZ II K is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to simple mounting, the FAZ II can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The zinc-plated steel version is used to fix loads in indoor areas. The steel anchor is, for example, suitable for fixing heavy steel constructions.

Advantages:

• The FAZ ll tried and tested expansion clip enables the highest load bearing capacity. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth (new also for M8 version) allows for significantly reduced drill hole depths and reduces the number of reinforcement hits. This allows for a noticeably quicker installation.
• Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process.
• The international approvals guarantee maximum safety and the best performane. These approvals even cover the use in earthquake zones (seismic performance) or the use of hollow drills.

Top Features:

• With expansion clip for maximum load-bearing capacity. Thus fewer fixing points and smaller anchor plates are required. This saves time and costs.
• Minimum torque slippage: Simple assembly saves time as well as wear and tear.
• With approval for cracked concrete and fire inspection: maximum safety.
• Ideal for high loads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-05/0069
• DoP No. 0009
• DoP No. 0081
• DoP No. 0121
• DoP No. 0756-CPD-0062
• ESR-2948

Approx. Rs 225 / Piece Get Latest Price

The economical solution for all standard fixings.

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 254 / Piece Get Latest Price

The economical solution for all standard fixings.

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 332 / Piece Get Latest Price

The economical solution for all standard fixings.

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 360 / Piece Get Latest Price

The economical solution for all standard fixings.

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 391 / Piece Get Latest Price

The economical solution for all standard fixings.

Advantages:

• Secure function and simple installation.
• Two Anchorage depths for more flexibility in the application.
• Use of hollow drills and diamond drills regulated in the European Technical Assessment ETA.
• Assortment: M 8 – M16, available in zinc-plated steel and stainless steel A4.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Concrete C12/15
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-17/0624
• DoP No. 0122

Approx. Rs 139 / Piece Get Latest Price

The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• Stainless steel: permanent safety in outdoor use.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Machines
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296

Approx. Rs 154 / Piece Get Latest Price

The cost-efficient fixing made of stainless steel for use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• Stainless steel: permanent safety in outdoor use.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Machines
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296

Approx. Rs 204 / Piece Get Latest Price

The cost-efficient fixing made of stainless steel for use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• Stainless steel: permanent safety in outdoor use.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296

Approx. Rs 666 / Piece Get Latest Price

he cost-efficient fixing made of stainless steel for use in non-cracked concrete.
he fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• Stainless steel: permanent safety in outdoor use.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296

Approx. Rs 1,632 / Piece Get Latest Price

The cost-efficient fixing made of stainless steel for use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Stainless steel: permanent safety in outdoor use.
• Ideal for high loads.

Applications:

• Steel constructions
• Consoles
• Machines
• Staircases
• Gates

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296

Approx. Rs 53 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Machines
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 73 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Machines
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 85 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The anchor is also ideal for large fixture thicknesses.
• The long thread balances component tolerances and stand-off installations, and thus increases flexibility.
• Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly.
• The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Machines
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
•  You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 218 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The anchor is also ideal for large fixture thicknesses.
• The long thread balances component tolerances and stand-off installations, and thus increases flexibility.
• Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly.
• The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 151 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The anchor is also ideal for large fixture thicknesses.
• The long thread balances component tolerances and stand-off installations, and thus increases flexibility.
• Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly.
• The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 20 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The anchor is also ideal for large fixture thicknesses.
• The long thread balances component tolerances and stand-off installations, and thus increases flexibility.
• Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly.
• The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 120 / Piece Get Latest Price

Short and strong: the cost-efficient fixing made of galvanised steel for use in non-cracked concrete.
The fischer bolt anchor FBN II K is a steel anchor for cost-effective fixings in non-cracked concrete. The short version is suitable for pre-positioned installation and push-through installation. The bolt anchor is made of zinc-plated steel and is recommended for railings, handrails or consoles in indoor areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• Maximum load-bearing capacity in non-cracked concrete. This means: fewer fixing points and smaller anchor plates.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 318 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The anchor is also ideal for large fixture thicknesses.
• The long thread balances component tolerances and stand-off installations, and thus increases flexibility.
• Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly.
• The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 311 / Piece Get Latest Price

Short and strong: the cost-efficient fixing made of galvanised steel for use in non-cracked concrete.
The fischer bolt anchor FBN II K is a steel anchor for cost-effective fixings in non-cracked concrete. The short version is suitable for pre-positioned installation and push-through installation. The bolt anchor is made of zinc-plated steel and is recommended for railings, handrails or consoles in indoor areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• Maximum load-bearing capacity in non-cracked concrete. This means: fewer fixing points and smaller anchor plates.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 151 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 329 / Piece Get Latest Price

Short and strong: the cost-efficient fixing made of galvanised steel for use in non-cracked concrete.
The fischer bolt anchor FBN II K is a steel anchor for cost-effective fixings in non-cracked concrete. The short version is suitable for pre-positioned installation and push-through installation. The bolt anchor is made of zinc-plated steel and is recommended for railings, handrails or consoles in indoor areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• Maximum load-bearing capacity in non-cracked concrete. This means: fewer fixing points and smaller anchor plates.
• Simple assembly due to few taps and minimal slippage.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 685 / Piece Get Latest Price

The cost-efficient fixing for flexible use in non-cracked concrete.
The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.

Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The anchor is also ideal for large fixture thicknesses.
• The long thread balances component tolerances and stand-off installations, and thus increases flexibility.
• Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly.
• The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• The drive-in pin protects the thread from damage. This saves time during installation and removal.
• Ideal for high loads.

Applications:

• Steel constructions
• Consoles
• Machines
• Staircases
• Gates

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure

* You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296
• GS 3.2/18-082-1-r1

Approx. Rs 90 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 137 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 232 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
•  You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 540 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
•  You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 662 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 53 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 56 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 61 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 61 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 74 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 101 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 107 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 3,305 / Piece Get Latest Price

Product Brochure
The fischer high-performance anchor FH II B with threaded bolt is a sleeve anchor made of zinc-plated steel. The anchor is set in the time-saving through-type installation. When tightening the anchor, the cone is pulled into the expansion sleeve and expands it against the hole wall. The black plastic ring prevents the anchor from rotating and absorbs the torque slippage. This means that the fixture is pulled towards the anchoring base. The fischer high-performance anchor FH II B with threaded bolt is ideally suited to fix railings, steel constructions, and cable trays in cracked and non-cracked concrete.

Advantages:

• The international approvals guarantee maximum safety and the best performance. The European Technical Assessment even cover use in earthquake zones (seismic C1 and C2).
• The practical fixing using washers and nuts allows for the ultimate removal of the attachment if required later.
• The design between the bolt and the sleeve ensures high shear load-bearing capacity. Thus, fewer fixing points are required.
• The optimised geometry intelligently reduces the energy required for assembly.
• The approval regulates the use of hollow drills.

Top Features:

• With threaded bolts.
• The international approvals guarantee maximum safety and maximum performance. Also for applications in earthquake regions (seismic C1 and C2).
• The ideal combination of screw shank and sleeve enables a high transverse load capacity and fewer fixing points.
• The optimised geometry intelligently reduces the setting energy and thus ensures a force-saving assembly.

Applications:

• Staircases
• Consoles
• Steel constructions
• Machines
• Gates

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-07/0025
• DoP No. 0020
• DoP No. 0127
• DoP No. 0756-CPD-0295
• ESR-2691

Approx. Rs 240 / Piece Get Latest Price

The fischer bolt anchor FAZ II is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to the two anchorage depths and simple mounting, the FAZ II can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The zinc-plated steel version is used to fix loads in indoor areas. The steel anchor is, for example, suitable for fixing railings, cable trays and consoles.Advantages

• According to the new evaluation (ETA), the tensile strengths are decisive. Thus fewer anchors are required.
• The variable anchorage depths with sizes M8 to M16 allow a millimetre-accurate adjustment to the loads for the first time. 
• The version with the cap nut offers an optically attractive anchoring and protects against injuries as well thanks to the round shape.
• The first bolt anchor M6 with an ETA assessment Option 1 for secure and reliable anchorings.
• The international approvals guarantee maximum safety and the best performance.
• Top Features
  • One anchor - two anchorage depths: Reduced anchorage depths save time and costs during drilling.
  • With expansion clip for maximum load-bearing capacity. Thus fewer fixing points and smaller anchor plates are required. This saves time and costs.
  • Minimum torque slippage: Simple assembly saves time as well as wear and tear.

Approx. Rs 293 / Piece Get Latest Price

The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas.Advantages

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.
• Top Features
  • The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
  • If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
  • Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
  • Simple assembly due to few taps and minimal slippage.
  • The drive-in pin protects the thread from damage. This saves time during installation and removal.

Approx. Rs 56 / Piece Get Latest Price

The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas.Advantages

• The special active principle allows for a simple hammerset installation and, therefore, a short processing time.
• The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation.
• The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations.
• The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety.
• A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use.
• Top Features
  • Hammerset installation saves time.
  • No reinforcement hits due to low anchorage depth This saves time and costs during series installation.
  • Expansion clip provides a firm hold.
  • ETA approval for multiple fixings.
  • Series installation possible with setting tool for the hammer drill. This saves time and costs.

Approx. Rs 37 / Piece Get Latest Price

The cost-effective high-performance anchor for push-through installations in non-cracked concrete.

Advantages:

• Easy to insert into the drill hole thanks to undersize
• High shear loads
• Removable

Applications:

• Handles
• Consoles
• Ladders
• Cable trays
• Gates
• Façades
• Temporary or structural fixings

Building Materials:
Suitable for:

• Concrete ≥ C12/15
• You can find detailed information on building materials in the registration document.

Approx. Rs 71 / Piece Get Latest Price

The cost-effective high-performance anchor for push-through installations in non-cracked concrete.

Advantages:

• Easy to insert into the drill hole thanks to undersize
• High shear loads
• Removable

Applications:

• Handles
• Consoles
• Ladders
• Cable trays
• Gates
• Façades
• Temporary or structural fixings

Building Materials:
Suitable for:

• Concrete ≥ C12/15
•  You can find detailed information on building materials in the registration document.