Steel Anchors 1

Approx. Rs 40 / Piece Get Latest Price

The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked

Approx. Rs 179 / Piece Get Latest Price

The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The stainless steel version of the bolt anchor is suitable for fixing façade sub-structures, consoles, and ladders in external areas.Advantages:

• The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility.
• Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation.
• The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment.

Top Features:

• The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates.
• If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation.
• Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility.
• Simple assembly due to few taps and minimal slippage.
• Stainless steel: permanent safety in outdoor use.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:Approved for:

• Concrete C20/25 to C50/60, non-cracked

Also suitable for:

• Concrete C12/15
• Natural stone with dense structure

Permission:

• ETA-07/0211
• DoP No. 0015
• DoP No. 0756-CPD-0296

Approx. Rs 255 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 137 / Piece Get Latest Price

Cost efficient fixing with ETA approval for non- cracked concrete.

Advantages:

• The standard anchorage depth achieves the maximum loadbearing capacities so fewer fixing points and smaller anchor plates are required.
• With only a few hammer blows and minimal torque slippage installation is a simple process.
• The drive-in pin protects the thread from damage, and ensures a faster installation and dismantling of the attachment.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, non-cracked
•  You can find detailed information on building materials in the registration document.

Permission:

• ETA-13/0772
• DoP No. 0034
• DoP No. 0756-CPD-0606

Approx. Rs 2,746 / Piece Get Latest Price

The fischer bolt anchor FAZ II K A4 is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to simple mounting, the FAZ II A4 can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The stainless steel version is used to fix loads in outdoor areas. The steel anchor is, for example, suitable for fixing heavy steel constructions.

Advantages:

• The FAZ ll tried and tested expansion clip enables the highest load bearing capacity. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth (new also for M8 version) allows for significantly reduced drill hole depths and reduces the number of reinforcement hits. This allows for a noticeably quicker installation.
• Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process.
• The international approvals guarantee maximum safety and the best performane. These approvals even cover the use in earthquake zones (seismic performance) or the use of hollow drills.
• Powerful connection: Expansion clip ensures optimum load-carrying properties. Fewer fixing points and smaller anchor plates save time and costs.
• Simple assembly: few taps and minimal torque slippage. This saves time and power.
• Stainless steel: maximum security for outdoor use.
• Ideal for high loads.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-05/0069
• DoP No. 0009
• DoP No. 0081
• DoP No. 0121
• DoP No. 0756-CPD-0062
• ESR-2948

Approx. Rs 1,403 / Piece Get Latest Price

The fischer anchor bolt FAZ II A4 is the steel anchor for maximum loads. Heavy loads are fastened in cracked concrete with the steel anchor. Thanks to the two anchorage depths and the easy installation, the FAZ II A4 can be used particularly flexibly. The proven expansion clip transfers loads particularly securely into the concrete and allows the maximum load-bearing capacity. With the stainless steel construction, loads are fastened outside. The steel anchor is ideal, for example, for fastening railings, brackets, steel constructions and gates.

Advantages:

• According to the new evaluation (ETA), the tensile strengths are decisive. Thus fewer anchors are required.
• The variable anchorage depths with sizes M8 to M16 allow a millimetre-accurate adjustment to the loads for the first time. 
• The version with the cap nut offers an optically attractive anchoring and protects against injuries as well thanks to the round shape.
• The first bolt anchor M6 with an ETA assessment Option 1 for secure and reliable anchorings.
• The international approvals guarantee maximum safety and the best performance.

  Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-05/0069
• DoP No. 0009
• DoP No. 0081
• DoP No. 0121
• DoP No. 0756-CPD-0062
• ESR-2948

Approx. Rs 71 / Piece Get Latest Price

The cost-effective hammerset anchor without approval for multiple fixings in non-structural systemsThe fischer hammerset anchor EA N is an internal thread anchor made from zinc-plated and stainless steel. The hammerset anchor is ideal for the multiple fixation of non-structural systems that do not require approved anchorage. The assembly of the internal thread anchor is extremely cost-effective thanks to the low embedment depth, fast hammerset installation, and direction-controlled screwing process. The EA N is mounted with the hammer flush to the base material. With the setting tool EA-ST, the sleeve is expanded and braced against the drill hole wall through the driving in of the internal pin. No torque should be applied to the screw to enable correct expansion.

Advantages:

• Simple hammerset installation
• The metric internal thread allows for the use of standard screws or threaded rods for ideal adaptation in line with the intended use.
• The hand setting tool EA-ST facilitates fast installation.

Top Features

• Simple hammerset installation.
• The metric internal thread allows for the use of standard screws or threaded rods for ideal adaptation in line with the intended use.
• The hand setting tool EA-ST facilitates fast installation.

Applications:

• Pipelines and ventilation ducts
• Sprinkler systems
• Steel constructions
• Consoles

Building Materials:

• Concrete C12/15, non-cracked
• Concrete C20/25, non-cracked
• You can find detailed information on building materials in the registration document.

Approx. Rs 785 / Piece Get Latest Price

The internal threaded anchor RG M I is made of zinc-plated steel. The internal threaded anchor is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the RG M I through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the internal threaded anchor is pushed into the drill hole manually by lightly rotating it. The various mortars bond the entire surface of the RG M I with the drill hole wall. The internal threaded anchor can be removed when surface-flush and is, for example, mainly suitable for temporary fixings such as for machines in internal areas.

Advantages:

• The internal threaded anchor RG MI is suitable for use with resin capsules or injection mortars in concrete.
• The internal threaded anchor RG MI allows for the surface-flush removal and reuse of the fixing point. It therefore offers great flexibility.
• The metric internal thread allows for the use of standard metric screws or threaded rods, which enables ideal adaptation in line with the intended use.
• Please refer to the approvals of the resin capsules and injection mortar used.

Top Features:

• Surface flush removal enables fixing point to be reused.
• Conventional screws and threaded rods can be used. This lowers costs and complexity.
• Suitable for anchorage in cracked and non-cracked concrete in combination with various mortar cartridges or injection mortars.

Applications:

• Removable and temporary fixings
• Anchorings with resin capsules RSB and RM II
• Anchorings with injection mortars FIS SB, FIS EM Plus, FIS V, FIS VL, and FIS Green in concrete

Building Materials:

• Concrete, cracked and non-cracked

Approx. Rs 433 / Piece Get Latest Price

The internal threaded anchor RG M I is made of zinc-plated steel. The internal threaded anchor is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the RG M I through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the internal threaded anchor is pushed into the drill hole manually by lightly rotating it. The various mortars bond the entire surface of the RG M I with the drill hole wall. The internal threaded anchor can be removed when surface-flush and is, for example, mainly suitable for temporary fixings such as for machines in internal areas.

Advantages:

• The internal threaded anchor RG MI is suitable for use with resin capsules or injection mortars in concrete.
• The internal threaded anchor RG MI allows for the surface-flush removal and reuse of the fixing point. It therefore offers great flexibility.
• The metric internal thread allows for the use of standard metric screws or threaded rods, which enables ideal adaptation in line with the intended use.
• Please refer to the approvals of the resin capsules and injection mortar used.

Top Features:

• Surface flush removal enables fixing point to be reused.
• Conventional screws and threaded rods can be used. This lowers costs and complexity.
• ETA approval for maximum safety.
• Suitable for anchorage in cracked and non-cracked concrete in combination with various mortar cartridges or injection mortars.

Applications:

• Removable and temporary fixings
• Anchorings with resin capsules RSB and RM II
• Anchorings with injection mortars FIS SB, FIS EM Plus, FIS V, FIS VL, and FIS GREEN in concrete

Building Materials:

• Concrete, cracked and non-cracked

Approx. Rs 3,690 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsule RM II
• Approved anchorings with Injection mortars FIS EM, FIS EB, FIS V and FIS VL

Building Materials:

• In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete.
• In connection with several fischer injection mortars approved or suitable for different building materials.

Approx. Rs 1,009 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V, FIS VL, FIS Green and FIS P Plus

Building Materials:

• In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete.
• In connection with several fischer injection mortars approved or suitable for different building materials.

Approx. Rs 78 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 5.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.

Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Top Features:

• The universal solution for various fischer injection mortars. For a manageable range and simpler storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V, FIS VL, FIS GREEN and FIS P Plus
• Anchorings without approval with Injection mortar FIS P

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.

Approx. Rs 424 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 8.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.

Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Top Features:

• The universal solution for various fischer injection mortars. This lowers complexity and simplifies storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.
• Metre-long units, cut to length as required.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS PM, FIS V, FIS VL, FIS P Plus and FIS GREEN
• Anchorings without approval with Injection mortar FIS P

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.

Approx. Rs 287 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 8.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.

Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Top Features:

• The universal solution for various fischer injection mortars. This lowers complexity and simplifies storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.
• Metre-long units, cut to length as required.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V, FIS VL, FIS GREEN and FIS P Plus
• Anchorings without approval with Injection mortar FIS P

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.

Approx. Rs 2,838 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V and FIS VL.

Approx. Rs 4,565 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V and FIS VL

Approx. Rs 2,336 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V and FIS VL

Approx. Rs 1,054 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V, FIS VL and FIS Green.

Approx. Rs 1,801 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V and FIS VL

Building Materials:

• In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete.
• In connection with several fischer injection mortars approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-02/0024, ETAG 001-5
• DoP No. 0007
• DoP No. 0072
• DoP No. 0094
• DoP No. 0094 - EN
• DoP No. 0756-CPD-0300
• DoP No. 0756-CPD-0301
• DoP No. 0756-CPD-0490

Approx. Rs 310 / Piece Get Latest Price

The fischer rod anchor RG M is made of zinc-plated steel with a grade of 5.8. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in internal areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Zinc-galvanised steel for internal use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V, FIS VL, FIS Green and FIS P Plus

Building Materials:

• In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete.
• In connection with several fischer injection mortars approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-02/0024, ETAG 001-5
• DoP No. 0007
• DoP No. 0072
• DoP No. 0094
• DoP No. 0094 - EN
• DoP No. 0756-CPD-0301
• DoP No. 0756-CPD-0490

Approx. Rs 1,723 / Piece Get Latest Price

The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Stainless steel for outdoor use.

Approx. Rs 1,114 / Piece Get Latest Price

The fischer rod anchor RG M is produced from stainless steel. The anchor rod is a systems accessory for various fischer mortar cartridges or injection mortars. Application with pre-portioned mortar cartridges is especially cost-effective for individual fixings. During mounting with the resin capsule, set the fischer anchor rod RG M through rotating and hitting motions with a hammer drill. The capsule is destroyed during the setting process, which mixes and activates the mortar compound. During mounting with injection mortars, the anchor rod is pushed into the drill hole manually by lightly rotating it. The system is particularly suitable for cost-effective fixing of machines, steelwork constructions, and supporting feet in external areas.

Advantages:

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Top Features:

• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various mortar cartridges or injection mortars.
• Anchor rod with oblique edge and hexagon for simple installation with pre-portioned injection cartridge.
• Stainless steel for outdoor use.

Applications:

• Approved anchorings with Resin capsules RSB and RM II
• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS V, FIS VL, FIS Green and FIS P Plus

Building Materials:

• In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete.
• In connection with several fischer injection mortars approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-02/0024, ETAG 001-5
• DoP No. 0007
• DoP No. 0072
• DoP No. 0094
• DoP No. 0094 - EN
• DoP No. 0756-CPD-0301
• DoP No. 0756-CPD-0490

Approx. Rs 440 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 5.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.


Top Features:

• The universal solution for various fischer injection mortars. For a manageable range and simpler storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.

Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS PM, FIS V, FIS VL and FIS GREEN
• Anchorings without approval with Injection mortars FIS P Plus and FIS P

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-02/0024, ETAG 001-5
• DoP No. 0007
• DoP No. 0072
• DoP No. 0094
• DoP No. 0094 - EN
• DoP No. 0756-CPD-0301
• ESR-3572

Approx. Rs 514 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 8.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.

Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Top Features:

• The universal solution for various fischer injection mortars. For a manageable range and simpler storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS PM, FIS V, FIS VL and FIS Green

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-02/0024, ETAG 001-5
• DoP No. 0007
• DoP No. 0072
• DoP No. 0094
• DoP No. 0094 - EN
• DoP No. 0756-CPD-0301
• ESR-3572

Approx. Rs 1,062 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 8.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.

Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Top Features:

• The universal solution for various fischer injection mortars. This lowers complexity and simplifies storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.
• Metre-long units, cut to length as required.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS PM, FIS V, FIS VL, FIS P Plus and FIS Green.
• Anchorings without approval with Injection mortar FIS P

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Approx. Rs 142 / Piece Get Latest Price

The cost-effective fixation without approval - for use in non-cracked concrete.The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked.

Approx. Rs 65 / Piece Get Latest Price

The cost-effective fixation without approval - for use in non-cracked concrete.The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked

Approx. Rs 18 / Piece Get Latest Price

The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked
• You can find detailed information on building materials in the registration document.

Approx. Rs 1,608 / Piece Get Latest Price

The fischer bolt anchor FAZ II K is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to simple mounting, the FAZ II can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The zinc-plated steel version is used to fix loads in indoor areas. The steel anchor is, for example, suitable for fixing heavy steel constructions.

Advantages:

• The FAZ ll tried and tested expansion clip enables the highest load bearing capacity. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth (new also for M8 version) allows for significantly reduced drill hole depths and reduces the number of reinforcement hits. This allows for a noticeably quicker installation.
• Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process.
• The international approvals guarantee maximum safety and the best performane. These approvals even cover the use in earthquake zones (seismic performance) or the use of hollow drills.

Top Features:

• With expansion clip for maximum load-bearing capacity. Thus fewer fixing points and smaller anchor plates are required. This saves time and costs.
• Minimum torque slippage: Simple assembly saves time as well as wear and tear.
• With approval for cracked concrete and fire inspection: maximum safety.
• Ideal for high loads.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-05/0069
• DoP No. 0009
• DoP No. 0081
• DoP No. 0121
• DoP No. 0756-CPD-0062
• ESR-2948

Approx. Rs 471 / Piece Get Latest Price

The fischer bolt anchor FAZ II is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to the two anchorage depths and simple mounting, the FAZ II can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The zinc-plated steel version is used to fix loads in indoor areas. The steel anchor is, for example, suitable for fixing railings, cable trays and consoles.

Advantages:

• According to the new evaluation (ETA), the tensile strengths are decisive. Thus fewer anchors are required.
• The variable anchorage depths with sizes M8 to M16 allow a millimetre-accurate adjustment to the loads for the first time. 
• The version with the cap nut offers an optically attractive anchoring and protects against injuries as well thanks to the round shape.
• The first bolt anchor M6 with an ETA assessment Option 1 for secure and reliable anchorings.
• The international approvals guarantee maximum safety and the best performance.

Top Features:

• One anchor - two anchorage depths: Reduced anchorage depths save time and costs during drilling.
• With expansion clip for maximum load-bearing capacity. Thus fewer fixing points and smaller anchor plates are required. This saves time and costs.
• Minimum torque slippage: Simple assembly saves time as well as wear and tear.
• With approval for cracked concrete and fire inspection: maximum safety.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-05/0069
• DoP No. 0009
• DoP No. 0081
• DoP No. 0121
• DoP No. 0756-CPD-0062
• ESR-2948

Approx. Rs 308 / Piece Get Latest Price

The fischer bolt anchor FAZ II is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to the two anchorage depths and simple mounting, the FAZ II can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The zinc-plated steel version is used to fix loads in indoor areas. The steel anchor is, for example, suitable for fixing railings, cable trays and consoles.

Advantages:

• According to the new evaluation (ETA), the tensile strengths are decisive. Thus fewer anchors are required.
• The variable anchorage depths with sizes M8 to M16 allow a millimetre-accurate adjustment to the loads for the first time. 
• The version with the cap nut offers an optically attractive anchoring and protects against injuries as well thanks to the round shape.
• The first bolt anchor M6 with an ETA assessment Option 1 for secure and reliable anchorings.
• The international approvals guarantee maximum safety and the best performance.

Top Features:

• One anchor - two anchorage depths: Reduced anchorage depths save time and costs during drilling.
• With expansion clip for maximum load-bearing capacity. Thus fewer fixing points and smaller anchor plates are required. This saves time and costs.
• Minimum torque slippage: Simple assembly saves time as well as wear and tear.
• With approval for cracked concrete and fire inspection: maximum safety.
• Ideal for large fixture thicknesses.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:
Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-05/0069
• DoP No. 0009
• DoP No. 0081
• DoP No. 0121
• DoP No. 0756-CPD-0062
• ESR-2948

Approx. Rs 372 / Piece Get Latest Price

The fischer bolt anchor FAZ II K A4 is the steel anchor for the most demanding requirements. Heavy loads are fixed into cracked concrete with the steel anchor. Due to simple mounting, the FAZ II A4 can be used in a particularly flexible manner. The proven expansion clip feeds the loads into the concrete in an especially secure manner and ensures maximum load-bearing properties. The stainless steel version is used to fix loads in outdoor areas. The steel anchor is, for example, suitable for fixing railings, consoles, steel constructions, and gates.

Advantages:

• The FAZ ll tried and tested expansion clip enables the highest load bearing capacity. Thus fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth (new also for M8 version) allows for significantly reduced drill hole depths and reduces the number of reinforcement hits. This allows for a noticeably quicker installation.
• Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process.

Top Features:

• Powerful connection: Expansion clip ensures optimum load-carrying properties. Fewer fixing points and smaller anchor plates save time and costs.
• Simple assembly: few taps and minimal torque slippage. This saves time and power.
• Stainless steel: maximum security for outdoor use.

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades
• Timber constructions

Building Materials:

Approved for:

• Concrete C20/25 to C50/60, cracked and non-cracked

Also suitable for:

• Concrete C12/15
• Concrete C80/95 (classification available)

Approx. Rs 30 / Piece Get Latest Price

The cost-effective fixation without approval - for use in non-cracked concrete.The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases

Approx. Rs 269 / Piece Get Latest Price

The cost-effective fixation without approval - for use in non-cracked concrete.The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Approx. Rs 103 / Piece Get Latest Price

The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked
• You can find detailed information on building materials in the registration document.

Approx. Rs 168 / Piece Get Latest Price

The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked
• You can find detailed information on building materials in the registration document.

Approx. Rs 179 / Piece Get Latest Price

The fischer bolt anchor FWA is an economical solution for all applications where an approved fixation is not required. The FWA is offered in zinc-plated steel and hot-dip galvanised steel with an imperial thread. The bolt anchor can be used with two anchorage depths. The standard anchorage depth guarantees a high load-bearing capacity. This means that fewer fixing points and smaller anchor plates are required. The reduced anchorage depth reduces the drill hole depth. This saves time during the installation and increases flexibility.

Advantages:

• The standard anchorage depth achieves high load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required.
• The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility.
• Available with metric and imperial threads

Applications:

• Steel constructions
• Guard rails
• Consoles
• Ladders
• Cable trays
• Machines
• Staircases
• Gates
• Façades

Building Materials:

• Concrete C20/25, non-cracked
• You can find detailed information on building materials in the registration document.

Approx. Rs 12 / Piece Get Latest Price

The fischer hammerset anchor EA N is an internal thread anchor made from zinc-plated and stainless steel. The hammerset anchor is ideal for the multiple fixation of non-structural systems that do not require approved anchorage. The assembly of the internal thread anchor is extremely cost-effective thanks to the low embedment depth, fast hammerset installation, and direction-controlled screwing process. The EA N is mounted with the hammer flush to the base material. With the setting tool EA-ST, the sleeve is expanded and braced against the drill hole wall through the driving in of the internal pin. No torque should be applied to the screw to enable correct expansion.
Advantages:

• Simple hammerset installation
• The metric internal thread allows for the use of standard screws or threaded rods for ideal adaptation in line with the intended use.
• The hand setting tool EA-ST facilitates fast installation.

Applications:

• Pipelines and ventilation ducts
• Sprinkler systems
• Steel constructions
• Consoles

Building Materials:

• Concrete C12/15, non-cracked
• Concrete C20/25, non-cracked
• You can find detailed information on building materials in the registration document.

Approx. Rs 15 / Piece Get Latest Price

The fischer hammerset anchor EA N is an internal thread anchor made from zinc-plated and stainless steel. The hammerset anchor is ideal for the multiple fixation of non-structural systems that do not require approved anchorage. The assembly of the internal thread anchor is extremely cost-effective thanks to the low embedment depth, fast hammerset installation, and direction-controlled screwing process. The EA N is mounted with the hammer flush to the base material. With the setting tool EA-ST, the sleeve is expanded and braced against the drill hole wall through the driving in of the internal pin. No torque should be applied to the screw to enable correct expansion.Advantages:

• Simple hammerset installation
• The metric internal thread allows for the use of standard screws or threaded rods for ideal adaptation in line with the intended use.
• The hand setting tool EA-ST facilitates fast installation.

Top Features:

• Simple hammerset installation.
• The metric internal thread allows for the use of standard screws or threaded rods for ideal adaptation in line with the intended use.
• The hand setting tool EA-ST facilitates fast installation.

Applications:

• Pipelines and ventilation ducts
• Sprinkler systems
• Steel constructions
• Consoles

Building Materials:

• Concrete C12/15, non-cracked
• Concrete C20/25, non-cracked

* You can find detailed information on building materials in the registration document.

Approx. Rs 182 / Piece Get Latest Price

The fischer threaded rod FIS A is made from zinc-plated, steel grade 5.8. The threaded rod is a system component for the various fischer injection mortars. Together with the injection mortars, the fischer threaded rods are suitable and approved for all subsurfaces. A thorough cleaning of the drill hole is recommended for the maximum load-bearing capacity of the system. The system, made from zinc-plated threaded rods in conjunction with fischer injection mortars, is suitable and approved for fixings in dry interiors.
Advantages:

• The threaded rod FIS A can be used with almost every fischer injection mortar (except Highbond special mortar FIS HB). It can be individually selected based on requirements, thus allowing for a wide range of applications.
• The wide range of approved threaded rods FIS A from M6 to M30 allows for various applications.
• Please refer to the approvals of the injection mortar used.

Top Features:

• The universal solution for various fischer injection mortars. For a manageable range and simpler storage.
• Approved for anchorage in cracked and non-cracked concrete, solid brick masonry, perforated masonry, and aerated concrete in combination with various fischer injection mortars.
• Optimum load adaptation due to variable anchorage depths. This lowers installation and material costs.

Applications:

• Approved anchorings with Injection mortars FIS SB, FIS EM, FIS EB, FIS PM, FIS V, FIS VL, FIS P Plus and FIS GREEN
• Anchorings without approval with Injection mortar FIS P

Building Materials:

• In connection with several fischer injection mortars the threaded rod FIS A is approved or suitable for different building materials.
• You can find detailed information on building materials in the registration document.

Permission:

• ETA-02/0024, ETAG 001-5
• DoP No. 0007
• DoP No. 0072
• DoP No. 0094
• DoP No. 0094 - EN
• DoP No. 0756-CPD-0301
• ESR-3572